Camloc® 2700 series quarter turn fasteners

Quarter-turn fasteners with flush head.

Typical usage is the quick installation of corner lights or light pods on rally cars, nose cones on formula cars, dashboard panels…

Maximum tensile strength: 1330 N
Working load: 900 N

Available with slotted or cross recess head.

Having the correct grip length is quite crucial to achieve the correct tension of the linkage.

When replacing or ordering spare parts for an existing application, check the small number stamped on the head of the stud. This shows the dash number which indicates stud length. It’s also possible to measure the total stud length and compare with our table below.

For the design of a new application you can consult our table below and accompanying drawings, containing information regarding which stud length and type of receptacle you need for the required total panel thickness [T].

Rivet type receptacles

Total length [T] = Panel 1 [P1] + Panel 2 [P2]

Threaded type receptacles

Total length [T] = Panel 1 [P1] + GAP (= min. 0,5 mm)

Steel zinc plated studs

Total Thickness [T]	Cross recess head	Slotted recess head	Total length [L]
0,75 - 1,50 mm	V27S02-1AGV	V27S01-1AGV	15,5 mm
1,50 - 2,30 mm	V27S02-2AGV	V27S01-2AGV	16,3 mm
2,30 - 3,05 mm	V27S02-3AGV	V27S01-3AGV	17,0 mm
3,05 - 3,80 mm	V27S02-4AGV	V27S01-4AGV	17,8 mm
3,80 - 4,60 mm	V27S02-5AGV	V27S01-5AGV	18,5 mm
4,60 - 5,35 mm	V27S02-6AGV	V27S01-6AGV	19,3 mm
5,35 - 6,10 mm	V27S02-7AGV	V27S01-7AGV	20,1 mm
6,10 - 6,85 mm	V27S02-8AGV	V27S01-8AGV	20,8 mm
6,85 - 7,60 mm	V27S02-9AGV	V27S01-9AGV	21,6 mm
7,60 - 8,40 mm	V27S02-10AGV	V27S01-10AGV	22,3 mm
8,40 - 9,15 mm	V27S02-11AGV	V27S01-11AGV	23,1 mm
9,15 - 9,90 mm	V27S02-12AGV	V27S01-12AGV	23,9 mm
9,90 - 10,65 mm	V27S02-13AGV	V27S01-13AGV	24,6 mm
10,65 - 11,40 mm	V27S02-14AGV	V27S01-14AGV	25,4 mm
11,40 - 12,20 mm	V27S02-15AGV	V27S01-15AGV	26,1 mm
12,20 - 12,95 mm	V27S02-16AGV	V27S01-16AGV	26,9 mm
12,95 - 13,70 mm	V27S02-17AGV	V27S01-17AGV	27,7 mm
13,70 - 14,50 mm	V27S02-18AGV	V27S01-18AGV	28,4 mm
14,50 - 15,25 mm	V27S02-19AGV	V27S01-19AGV	29,2 mm
15,25 - 16,00 mm	V27S02-20AGV	V27S01-20AGV	29,9 mm
16,00 - 16,75 mm	V27S02-21AGV	V27S01-21AGV	30,7 mm
16,75 - 17,50 mm	V27S02-22AGV	V27S01-22AGV	31,5 mm
17,50 - 18,30 mm	V27S02-23AGV	V27S01-23AGV	32,2 mm
18,30 - 19,05 mm	V27S02-24AGV	V27S01-24AGV	33,0 mm
19,05 - 19,80 mm	V27S02-25AGV	V27S01-25AGV	33,7 mm
19,80 - 20,60 mm	V27S02-26AGV	V27S01-26AGV	34,5 mm
20,60 - 21,35 mm	V27S02-27AGV	V27S01-27AGV	35,3 mm
21,35 - 22,10 mm	V27S02-28AGV	V27S01-28AGV	36,0 mm
22,10 - 22,85 mm	V27S02-29AGV	V27S01-29AGV	36,8 mm
22,85 - 23,60 mm	V27S02-30AGV	V27S01-30AGV	37,5 mm
23,60 - 24,40 mm	V27S02-31AGV	V27S01-31AGV	38,3 mm
24,40 - 25,15 mm	V27S02-32AGV	V27S01-32AGV	39,1 mm
25,15 - 25,90 mm	V27S02-33AGV	V27S01-33AGV	39,8 mm
25,90 - 26,65 mm	V27S02-34AGV	V27S01-34AGV	40,6 mm
26,65 - 27,40 mm	V27S02-35AGV	V27S01-35AGV	41,3 mm
27,40 - 28,20 mm	V27S02-36AGV	V27S01-36AGV	42,1 mm
28,20 - 28,95 mm	V27S02-37AGV	V27S01-37AGV	42,9 mm
28,95 - 29,70 mm	V27S02-38AGV	V27S01-38AGV	43,6 mm
29,70 - 30,50 mm	V27S02-39AGV	V27S01-39AGV	44,4 mm
30,50 - 31,25 mm	V27S02-40AGV	V27S01-40AGV	45,1 mm

Stainless steel studs

Total Thickness [T]	Slotted recess head	Total length [L]
0,75 - 1,50 mm	2700-1S	15,5 mm
1,50 - 2,30 mm	2700-2S	16,3 mm
2,30 - 3,05 mm	2700-3S	17,0 mm
3,05 - 3,80 mm	2700-4S	17,8 mm
3,80 - 4,60 mm	2700-5S	18,5 mm
4,60 - 5,35 mm	2700-6S	19,3 mm
5,35 - 6,10 mm	2700-7S	20,1 mm
6,10 - 6,85 mm	2700-8S	20,8 mm
6,85 - 7,60 mm	2700-9S	21,6 mm
7,60 - 8,40 mm	2700-10S	22,3 mm
8,40 - 9,15 mm	2700-11S	23,1 mm
9,15 - 9,90 mm	2700-12S	23,9 mm
9,90 - 10,65 mm	2700-13S	24,6 mm
10,65 - 11,40 mm	2700-14S	25,4 mm
11,40 - 12,20 mm	2700-15S	26,1 mm
12,20 - 12,95 mm	2700-16S	26,9 mm
12,95 - 13,70 mm	2700-17S	27,7 mm
13,70 - 14,50 mm	2700-18S	28,4 mm
14,50 - 15,25 mm	2700-19S	29,2 mm
15,25 - 16,00 mm	2700-20S	29,9 mm
16,00 - 16,75 mm	2700-21S	30,7 mm
16,75 - 17,50 mm	2700-22S	31,5 mm
17,50 - 18,30 mm	2700-23S	32,2 mm
18,30 - 19,05 mm	2700-24S	33,0 mm
19,05 - 19,80 mm	2700-25S	33,7 mm
19,80 - 20,60 mm	2700-26S	34,5 mm
20,60 - 21,35 mm	2700-27S	35,3 mm
21,35 - 22,10 mm	2700-28S	36,0 mm
22,10 - 22,85 mm	2700-29S	36,8 mm
22,85 - 23,60 mm	2700-30S	37,5 mm
23,60 - 24,40 mm	2700-31S	38,3 mm
24,40 - 25,15 mm	2700-32S	39,1 mm
25,15 - 25,90 mm	2700-33S	39,8 mm
25,90 - 26,65 mm	2700-34S	40,6 mm
26,65 - 27,40 mm	2700-35S	41,3 mm
27,40 - 28,20 mm	2700-36S	42,1 mm
28,20 - 28,95 mm	2700-37S	42,9 mm
28,95 - 29,70 mm	2700-38S	43,6 mm
29,70 - 30,50 mm	2700-39S	44,4 mm
30,50 - 31,25 mm	2700-40S	45,1 mm

¹ maximum tensile strength for the stainless steel studs is 1.000 N

Retaining washers for Camloc 2700 series studs

2600-SW
floating retaining washer

Stainless steel floating retaining washer for Camloc 2700 series quarter turns.

Camloc 2600-SW retaining washer

This retaining washer is to be used when the stud length number is 5 or greater.

On the drawing you can see how to prepare the panel depending on the panel thickness.

A floating retaining washer is often used with larger stud lengths. Also when the panel is curved it is easier to install the panel when the stud can move freely

V27-W01-1AN
fixed retaining washer

Steel nickel plated fixed retaining washer for Camloc 2700 series quarter turns.

Camloc V2600-LW-7 retaining washer

This washer has a higher spring profile so it fits the protruding cup of the stud in thin panels with a thickness of 2mm or less.

This retaining washer can be used with all the different stud length numbers.

On the drawing you can see how to prepare the panel depending on the panel thickness.

V2600-LW-7
fixed retaining washer

Stainless steel fixed retaining washer for Camloc 2700 series quarter turns.

Camloc V2600-LW-7 retaining washer

This retaining washer can be used with all the different stud length numbers in panels with a thickness of 2mm or thicker.

On the drawing you can see how to prepare the panel depending on the panel thickness.

This washer works very well with rather flat panels.

Camloc® 2600 & 2700 series rivet type receptacles

V26R6-1AGV lightweight receptacle

This lightweight receptacle is made of steel and is zinc plated (CrVI-free, clear passivation). The maximum application temperature is 120 °C.

Camloc V26R6-1AGV receptacle The rivet holes are 2,6mm so installation can be done with 2.4mm (or 3/32″) diameter rivets.

V212-12-1FGV and V212-12-2FGV cast receptacles

These cast receptacles are made of hard bronze and are zinc plated (CrVI-free, clear passivation). The maximum application temperature is 120 °C.

Camloc V212-12-1FGV and V212-12-2FGV receptacles For V212-12-1FGV, the rivet holes are 2,5mm so installation can be done with 2.4mm (or 3/32″) diameter rivets.

For V212-12-2FGV, the rivet holes are 3,3mm so installation can be done with 3,2mm (or 1/8″) diameter rivets.

Installation instructions for the rivet type receptacles

To prepare the bottom panel B for the receptacle, please follow these steps:

Drill a pilot hole in the center (where the stud will finally go through).
Drill the rivet holes with a center to center distance of 19mm.
Depending on the choosen receptacle, the diameter of these rivet holes will either be 2,5mm or 3,3mm.
Countersink the rivet holes to fit the countersink head of the choosen rivets.
Enlarge the pilot hole to the final size with a drill of 12,7mm diameter.

Camloc® 2600 & 2700 series threaded receptacle

99R10-01A1 threaded receptacle

This threaded receptacle is made of zinc die cast and is zinc plated (CrVI-free, clear chromate). The maximum application temperature is 100 °C.

Camloc 99R10-01A1 threaded receptacle

The threaded receptacle is used for single hole mounting applications.

The top of the receptacle is 100° countersunk.

There are 2 options for the use of this threaded receptacle:

installation together with the corresponding nut 99N10-01A1
installation in a threaded hole with 15/32-32UNS-2B female thread

99N10-01A1 nut for threaded receptacle

This receptacle nut is made of steel and is zinc plated (CrVI-free, clear chromate). The maximum application temperature is 100 °C.

Camloc 99N10-01A1 nut for 99R10-01A1 receptacle

This lightweight (stamped and formed) nut has 15/32-32UNS-2B thread to fit with the 99R10-01A1 threaded receptacle.

The advised fastening torque to apply when installing this nut on the receptacle is 3 Nm.

Installation instructions for the threaded receptacle

Installation with nut for panel thickness up to 2,3mm:

drill a pilot hole in the center
enlarge the pilot hole to the final diameter of 12mm
dimple the hole to 100° with the largest diameter at 17mm

Installation with nut for panel thickness of 2,3mm to 10,7mm:

drill a pilot hole in the center
enlarge the pilot hole to the final diameter of 12mm
countersink the hole at 100° with the largest diameter at 17mm

Installation without nut:

drill a pilot hole in the center
enlarge the pilot hole to a diameter of 11mm
countersink the hole at 100° with the largest diameter at 17mm
use a 15/32-32NS-2B tap to tap the thread for the receptacle
(for a blind installation, make sure the depth of the tapped thread is at least 16mm)

Camloc® is a registered brand of Howmet Fastening Systems

Camloc® 2700 series quarter turn fasteners